|Place of Origin:||China|
|Brand Name:||Dahua Sling|
|Certification:||OSHA regulations WSTDA standard|
|Model Number:||web sling|
|Minimum Order Quantity:||1000 pcs|
|Price:||USD 30,000 / 20'GP|
|Individual Certificates:||Provide Each Sling||Logo:||We Do It Oursleves|
|Eye Protector:||White Black Or Same As Webbing||Material:||100 % Polyester|
|Layer::||1 Layer||Width::||1 In, 2 Inches, 3 Inches|
|Standard:||OSHA Regulations WSTDA Standard||Packing:||Blank Or Printed|
|Sling Type:||Type 5 Endless||Item:||Synthetic Web Sling|
|Sling Length::||1 - 20 FT|
flat webbing sling,
webbing sling belt
Heavy Duty Synthetic Web Slings Endless Loop - Type 5 Synthetic Web Sling Yellow Polyester tuff tag
All lifting straps manufactured or provided by NANJING DAHUA meet or exceed all OSHA regulations as well as WSTDA standards.
Eye & Eye Tuff-Edge II Sling. Expect longer life, and lower overall cost with Tuff-Edge sling series. Tuff-Edge is more resistance to abrasion and edge cutting properties, giving you greater sling life and reduced sling costs.
|Lift-All Tuff-Edge II Eye & Eye Slings|
|One Ply||EE1801TF 1” Wide||1,600 lbs.||1,280 lbs.||3,200 lbs.|
|One Ply||EE1802TF 2” Wide||3,200 lbs.||2,500 lbs.||6,400 lbs.|
|One Ply||EE1803TF 3” Wide||4,800 lbs.||3,800 lbs.||9,600 lbs.|
|Two Ply||EE2801TF 1” Wide||3,200 lbs.||2,500 lbs.||6,400 lbs.|
|Two Ply||EE2802TF 2” Wide||6,400 lbs.||5,000 lbs.||12,800 lbs.|
|Two Ply||EE2803TF 3” Wide||8,800 lbs.||7,040 lbs.||
- Do not attempt to use sling above rated lifting capacity.
- When selecting a sling,it is very important to consider the angles at which the sling will be used.
- Slings are subject to cutting when ifting items with sharp egeds.In this case,always use protective sleeves
- Do not use a damaged sling,and se only if trained.
- Do not tie knots in sling webbing as strength is greatly reduced.
- Never drag a sling beneth from a load which is resting on it.
- Chemical active environments can affect the strength of slings
- Inspect slings weekly or more frequently depending on the sling use conditions.
- Always strore slings in a cool,dry and dark place to extend the working lift.
- Always read and understand the operating instructions before use.
- Failure to comply with this warning may result in serious load damageand death or injury.
Polyester is resistant to moderate strength acids but is damaged by alkalis; polyamide (Nylon) is virtually immune to
alkalis but is damaged by acids; and polypropylene is little affected by acids or alkalis but is damaged by some
solvents, tars and paints.
The sling must be both long enough and strong enough for the load and the slinging method. Apply the mode factor
for the slinging method. For use at temperatures exceeding 80°C or below 0°C refer to the suppliers instructions. If
the slings are used in multi-leg arrangement the angle formed between the legs should not be less than 30° or
greater than 90°. If abrasion, heat generated by friction or cutting from edges or corners are likely, select a sling
fitted with protective sleeves and/or use suitable packing.
Storing and Handling Belt Slings
Never return wet, damaged or contaminated slings to storage. They should be cleaned with clear water and dried
naturally. Never force dry belt slings. Store belt slings hung from non-rusting pegs which allow the free circulation of
air. The storage area should be dry, clean, free of any contaminates and shaded from direct sunlight. Do not alter,
modify or repair a belt sling but refer such matters to a Competent Person.
NOTE: The material from which the sling is manufactured may be identified by the colour of the label or printing on
the label: Polyester = Blue, Polyamide (Nylon) = Green, Polypropylene = Brown and the sling may also be dyed with
a colour code to indicate SWL.
Using Belt Slings Safely
Do not attempt lifting operations unless you understand the use of the equipment, the slinging procedures and the
mode factors to be applied. Do not use defective slings or accessories. Check the correct engagement with fittings
and appliances, ensure smooth radii are formed, do not twist or cross slings and do not overcrowd fittings. Position
the sling so that the load is uniformly spread over its width. Position the bight for a choke lift at the natural (120°)
angle to prevent friction being generated. Ensure that stitching is in the standing part of the sling away from hooks
and other fittings. Take the load steadily and avoid shock loads. Do not leave suspended loads unattended. In an
emergency cordon off the area.
In-service Inspection, Maintenance and Replacement
Inspect slings each day before use, looking for:
Do not use worn or damaged slings or attachments. Discard or repair them. Use damaged slings only after they are repaired, reconditioned, and proof tested by the sling manufacturer or a qualified person. Keep certificates of proof test.
Maintenance requirements are minimal. Belt slings may be cleaned with clear water. Remember weak chemical
solutions will become increasingly stronger by evaporation. Regularly inspect belt slings and, in the event of the
following defects, refer the sling to a Competent Person for thorough examination: illegible markings; damaged,
chaffed or cut webbing; damaged or loose stitching; heat damage; burns; chemical damage; solar degradation;
damaged or deformed end fittings.
Contact Person: jack